no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+Parts list for [[ZOMGTHEREMINBBQLOL]]
+(HA) Headphone output amp circuit(VC) Volume Control Voltage output circuit(PG) Pitch Control and Gate output circuit(TA) Output amp for tuner
+All capacitors are 50V 10% Ceramic unless othewise noted
+C2,C6 15pFC16 22pF NPOC9 33pF 5% NPOC1(HA),C7(PG) 100pFC8(PG) 330pFC12,C1(TA),C2(PG),C3(PG),C4(PG) 1nFC14 1800pF 5% polypropylene or polystyreneC1,C5 3300pF 5% polypropylene or polystyreneC24 3300pFC23 4700pF C15 6800pF polyesterC3,C7,C26 0.01μF polyesterC9(PG),C10(PG) 10nFC21,C22,C27,C28 .1μF C5(PG),C6(PG) 100nF PolypropyleneC1(PG) 220nFC29,C30,C10,C11 0.47μFC4,C8,C17,C18,C25 1μF 35V tantalumC13 22μFC19,C20 2200μF 35V aluminum electrolitic
+D1,D4,D5 1N4148 signal diodeD2,D3 1N4001 power diodeD1(PG),D2(PG) 1N4148 or 1N914B Diode
+L7,L8 2.5mH 3 section RF chokeL9 5mH 3 section RF chokeL1,L2 10mH 3 section RF chokeL3 25mH 3 section RF chokeL11 66μH Variable inductorL5,L6 100μH Variable inductor
+P1(PG) 10k multiturn trimmerP2(PG) 50k multiturn trimmerP1,P2 5kΩ potenitometer linear taperP3,P4 50kΩ potenitometer linear taperP5 50kΩ potenitometer audio
+Q1(PG) 2N3906 PNP transistorQ1-Q8,Q2(PG) 2N3904 NPN transistor
+All Resistors are 1/4W 5% unless otherwise noted
+R11,R20 33ΩR3(HA),R4(HA) 330ΩR1,R4,R5,R8,R3(TA),R3(HA) 1kΩR16(PG) 1kΩ PTC ThermesistorR2,R6,R13,R16,R21,R24(PG) 2.2kΩR18 2.7kΩR24,R26,R31,R32,R33,R34 4.7kΩR9,R12,R22,R23,R39,R40 10KΩR1(TA),R1(HA),R6(PG),R7(PG) 10kΩR20(PG),R21(PG),R25(PG) 10kΩR3(PG),R4(PG),R5(PG),R12(PG),R13(PG) 22kΩR3,R7,R30,R38,R2(TA),R1(PG) 47kΩR2(PG),R15(PG),R18(PG) 47kΩR29,R2(HA),R26(PG) 100KΩR27,R28 150kΩR4(TA)R17(PG) 220kΩR25,R10(PG),R11(PG),R19(PG) 330kΩR10,R15,R17,R19,R28(PG),R31(PG) 470kΩR8(PG),R9(PG) 680kΩR14,R36,R29(PG),R30(PG) 1MΩR14(PG) 1.2MΩR37 3.3MΩR35 4.7MΩR22(PG),R23(PG),R27(PG) 10MΩ
+U1 LM78L12 12V positive regulatorU2 LM79L12 12V negative regulatorU1(HA) TL081 Operational AmplifierU1(TA) LM3080N or CA3080E integrated circuitU3,U1(PG) LM13700N Dual Operational transconductance amplifierU2(PG),U8(PG) CD4093E Quad 2-input NAND Schmitt TriggerU3(PG) CD4022E Divide by 8 Johnson counterU4(PG),U6(PG) TL062 Operational AmplifierU5(PG) 4016 Quad Bilateral SwitchU7(PG) LM3046 or LM3086 Transistor Array
+rocker switches SPST5 1/4 Mono Jacks1 1/4 stereo jack1 14VAC 200mA transformer1 black box case for transformer1 3 prong grounded power cable1 3 pin DIN female1 3 pin DIN male15 Knobs for potentiometerssurface mount microphone mounting flange (Atlas AD-11B or equivalent)2 24-36" x 3/8" stright copper tubes for Antenna1/2" thick wood for 6"x18"x2" caseblank Copper PCBs for millingIC sockets 16 pin for U3 and U8(PG)connectors set from board to pannel and jacks on bottom(ribbon cable perhaps?)