User Tools

Site Tools


goodfet31

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

goodfet31 [2013/08/13 12:13] (current)
Line 1: Line 1:
 +**BOM DigiKey**
 +<​code>​
 + *1 [[http://​search.digikey.com/​scripts/​DkSearch/​dksus.dll?​vendor=0&​keywords=296-21439-1-ND 296-21439-1-ND]] IC MCU 16BIT 32K FLASH 38-TSSOP ​ $7.35 
 + *1 [[http://​search.digikey.com/​scripts/​DkSearch/​dksus.dll?​vendor=0&​keywords=768-1007-1-ND 768-1007-1-ND]] IC USB TO SERIAL UART 28-SSOP ​    ​$4.50</​code>​
 +
 +Once again, you can get your MSP430 from the nice folks at TI:   ​[[http://​focus.ti.com/​docs/​prod/​folders/​print/​msp430f2274.html#​MSP430F2274IDAR|MSP430F2274IDAR]] or [[http://​focus.ti.com/​docs/​prod/​folders/​print/​msp430f2274.html#​MSP430F2274TDAR|MSP430F2274TDAR]]. ​ This is the TSSOP 38 package, and you can get 2 free units of each.
 +
 +
 +Goodfet41
 +http:<​nowiki>//</​nowiki>​goodfet.sourceforge.net/​hardware/​goodfet41/​
 +
 +
 +  * 2 x 0.1uF 0603 capacitors
 +  * 1 x 330 Ohm 0603 resistor
 +  * 1 x 300 Ohm 0603 resistor
 +  * 3 x RED LED 0603
 +
 +
 +Rest of the parts, except the header, are shared with the [[GoodFET31L]]
 +
 +**Assembly Notes**
 +
 +Should take about 30 minutes to assemble.
 +
 +
 +If you're using [[http://​parts.digikey.com/​1/​parts/​682431-led-super-red-clear-0603-smd-ltst-c190krkt.html|this LED]], and using the arrows on the board, I believe the "large U" should be on the same side as the arrow head. The cathode (negative) is the T shaped pad.
 +
 +
 +FT232, resistors, LED's and capacitors added
 +
 +[[Image:​Goodfet.jpg]]
 +
 +
 +  *  Add FT232, tag corners or hot plate, check orientation.
 +  *  Add 0.1uF capacitors, can go around either way.
 +  *  Add 300 and 330Ohm resistors, can go around either way.
 +  *  Add 3 LEDs, check orientation.
 +
 +
 +Plug into a USB hub, Two LED's closest to the USB port should flash momentarily. If this works, plug it into a PC and the LED's should flash a couple of times more, and the PC should install drivers.
 +
 +If it doesn'​t flash, check orientation of the LEDs, if the USB doesn'​t install, check the chip for shorts or badly soldered pins.
 +
 +[[http://​sourceforge.net/​projects/​goodfet/​files/​|GoodFET Files on SourceForge]]
  
goodfet31.txt ยท Last modified: 2013/08/13 12:13 (external edit)